Video-mount-products FP-MWAB Manuel d'utilisateur télécharger pdf

IMPORTANT! For safety reasons, the concrete wall must be

capable of supporting the combined weight of the mount and the

display. The manufacturer takes no responsibility for failure caused

by walls of insucient strength.

Set the mount aside and drill a 10

mm (3/8”) hole at each marked

location. Remove any excess dust

from the holes.

Insert a concrete anchor (C) into

each hole so that it is ush with the

concrete surface (see Fig. 4). A

hammer can be used to lightly tap

the anchors into place if necessary.

NOTE: If the concrete wall is covered

by a layer of plaster or drywall, the

concrete anchor must pass

completely through the layer to rest

ush with the concrete surface.

Place the mount against the wall

over the drilled holes, making sure

the arrow on the mount points up.

Attach the mount to the wall using

the lag bolts (A) and lag bolt

washers (B) provided (see Fig. 5). Do

not over-tighten these bolts and

do not release the mount until all

bolts are in place. Ensure that the

mount remains level after all bolts

are secured.

Part 2 – Attaching the Mount Arms to the Display

(continued)

INSTRUCTION MANUAL

Display Size: 27” to 42”

Maximum Load: 80 lbs

Mounting Pattern: Up to 450 mm x 400 mm

Tilt Range: +15° to -15°

Prole: 5.5” to 16.5”

Read these instructions before you begin. If you are

unsure of any part of the process, contact a professional

contractor or installer for assistance. Improper installation

can result in injury or damage.

The wall or mounting surface must be capable of

supporting the combined weight of the mount and the

display; if not, the structure must be reinforced.

Locate pipes, wires, or any other hazards in the wall where

you wish to install the mount before drilling.

Safety gear and proper tools must be used. Failure to do so

can result in injury or damage.

A minimum of two people are required for installation. Do

not attempt to install this mount alone under any

circumstances.

Follow all instructions and recommendations regarding

adequate ventilation and suitable locations for mounting

your display. Consult the owner‘s manual for your particular

display for more information.

IMPORTANT! For safety reasons, this mount must be secured to a

wood stud capable of supporting the combined weight of the

mount and display. Do not mount to drywall alone.

IMPORTANT! The safety tabs and stoppers must be used at all

times to prevent the display from being accidentally knocked from

the mount.

SPECIFICATIONS

OPERATION AND ADJUSTMENT

BOX CONTENTS

HARDWARE KIT

TOOLS REQUIRED

INSTALLATION

WARNINGS

WARNINGS (continued)

Fig. 2

Phillips Head Screw Driver

Ratchet or Driver with 13 mm (1/2”) Socket

Electric or Portable Drill

6 mm (1/4”) Drill Bit and Stud Finder for Drywall Installation

10 mm (3/8”) Masonry Bit for Concrete Installation

Level

Full-motion Mount (x1)

Mount Arm (x2)

Instruction Manual (x1)

Hardware Kit (x1)

Part 1B – Mounting to the Wall (Concrete)

Fig. 3

Fig. 4

NOTE: This mount comes with a selection of dierent screw

diameters and lengths to accommodate a wide variety of

display models. Not all of the hardware in the kit will be used. If

you cannot nd the appropriate screw size in the kit provided,

consult the manufacturer of your display for more information.

Part 2 – Attaching the Mount Arms to the Display

IMPORTANT! Use extra care during this part of the installation. If

possible, avoid placing your display facedown as it may damage

the viewing surface.

Part 1A – Mounting to the Wall (Drywall)

Part 1B – Mounting to the Wall (Concrete)

(continued)

Place the mount against the wall in the desired location.

Make sure it is level.

While another person holds the mount in place, mark four

locations (two at the top and two at the bottom) for

securing the mount to the wall (see Fig. 3).

Fig. 1

Use a high quality stud nder to locate a stud where you

wish to install your mount. Mark both edges of the stud to

help identify the exact center.

NOTE: You must use the center of the stud to avoid

cracking or splitting the wood during installation.

Place the mount against the wall over the marked stud.

Make sure it is level.

While another person holds the mount in position, mark

two locations (one at the top and one at the bottom) for

securing the mount to the wall (see Fig. 1).

Set the mount aside and drill a 6 mm (1/4”) pilot hole at

each marked location.

Place the mount against the wall over the drilled holes,

making sure the arrow on the mount points up. Attach the

mount to the wall using the lag bolts (A) and lag bolt

washers (B) provided (see Fig. 2). Do not over-tighten

these bolts and do not release the mount until both

bolts are in place. Ensure that the mount remains level

after all bolts are secured.

Determine the correct diameter of screw to use by carefully

trying one of each size (M4, M6 and M8) from the hardware

kit. Do not force any of the screws – if you feel resistance

stop immediately and try a smaller diameter screw.

Attach the mount arms to the back of your display using

the screws identied in steps 1 and 2 (see Fig. 6):

If you are using the M4 or M6 screws you will also need

to use the M6 washers (J). M8 screws do not require

washers.

If you are using the longer screws on a display with a

curved or recessed back, you may also need to use the

spacers (K). Use one spacer or two spacers stacked as

needed.

Only use a spacer if necessary.

NOTE: The mount arms must be attached with the safety

tabs facing outward (i.e. away from the middle of the

display) (see Fig. 7). Otherwise, the safety tabs cannot be

easily accessed.

Determine the correct length of screw to use by examining

the back of your display:

If the back of your display is at and the mounting holes

are ush with the surface, you will use the shorter screws

(D, F or H) from the hardware kit.

If the back of your display is curved, has a protrusion, or if

the mounting holes are recessed, you will need to use the

longer screws (E, G or I) and may also need to use the

spacers (K).

Part 3 – Final Assembly

Part 3 – Final Assembly (continued)

With the help of another person, carefully lift your

display and place it on the mount.

Do not release the

display until the mount arms have securely hooked onto

the mount.

Move the safety tab located on each arm into position

so that it prevents the display from being lifted from the

mount. Insert a safety stopper (L) into each tab to keep it

in place. A padlock (not included) can be used in place

of one of the safety stoppers to help prevent unwanted

removal of the display.

Cables can be routed through the hooks located on the

mount to keep them organized and out of the way.

To change the tilt angle of your display, have one person

hold the display rmly in place while another person

loosens the tilt knobs located on each side of the mount.

Once loosened, you may move your display to the desired

position. Re-tighten the tilt knobs to lock the tilt angle in

place.

Do not release the display until the tilt knobs are

fully tightened.

NOTE:

The tilt adjustment knobs have a ratchet feature. If

you need to change the position of the knob without

tightening or loosening it, simply pull the knob outward

before turning.

Swivel adjustments can be made by grasping the display

rmly and moving it to the desired position. Be careful that

ngers or cables do not get pinched when moving the

mount. If any of the swivel joints are too tight or too loose,

they can be adjusted using the S4 Allen key (M) from the

hardware kit.

Periodically clean your mount with a dry cloth. Inspect all

screws and hardware at regular intervals to ensure that no

connections have become loose over time. Re-tighten as

needed.

CAUTION: This wall mount is intended for use only with

the maximum weight of 80 lbs. Use with heavier than the

maximum weights indicated may result in instability

causing possible injury.

FULL MOTION WALL MOUNT

FOR LCD, PLASMA, and LED DISPLAYS

Fig. 6

For displays with curved

or recessed backs.

For displays with

at backs.

Fig. 5

(A) M8 x 63 Lag Bolt (x4)

(B) Lag Bolt Washer (x4)

(D) M4 x 12 Screw (x4)

(F) M6 x 12 Screw (x4)

(E) M4 x 20 Screw (x4)

(G) M6 x 30 Screw (x4)

(I) M8 x 30 Screw (x4)

(H) M8 x 12 Screw (x4)

(J) M6 Washer (x4)

(K) Spacer (x8)

(M) S4 Allen Key (x1)

(L) Safety Stopper (x2)

Fig. 7

Safety Tab

FP-MWAB

Phone number: 877-281-2169

INSTRUCTION MANUAL 1

Résumé du contenu

Page 1 - INSTRUCTION MANUAL

IMPORTANT! For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and the display. The manufacturer take

Commentaires sur ces manuels

Pas de commentaire

Video-mount-products FP-MWAB Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Video-mount-products FP-MWAB. Video Mount Products FP-MWAB User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Video-mount-products FP-MWAB